Superconducting spin valve effect in Co/Pb/Co heterostructures with insulating interlayers

• Andrey A. Kamashev,
• Nadir N. Garif’yanov,
• Aidar A. Validov,
• Vladislav Kataev,
• Alexander S. Osin,
• Yakov V. Fominov and
• Ilgiz A. Garifullin

Beilstein J. Nanotechnol. 2024, 15, 457–464, doi:10.3762/bjnano.15.41

• was measured by a Hall probe with an accuracy of ±0.3 Oe. The sample temperature was monitored using an Allen-Bradley thermometer that is highly sensitive in the temperature range of interest. The temperature measurement error was ±(5–6) mK below 3 K. The superconducting critical temperature Tc was

Experimental investigation of usage of POE lubricants with Al₂O₃, graphene or CNT nanoparticles in a refrigeration compressor

• Kayhan Dağıdır and
• Kemal Bilen

Beilstein J. Nanotechnol. 2023, 14, 1041–1058, doi:10.3762/bjnano.14.86

• . Details of the experimental investigation are presented in the following sections. Experimental setup The experimental setup includes a semi-hermetic reciprocating compressor. This compressor is compatible with the refrigerant R1234yf. The experimental setup is shown in Figure 1. Pressure and temperature

• measurement devices were placed to control operating conditions at the inlet and outlet of the compressor. Pressure and temperature values were measured at the inlet and outlet to ensure safe operation of the refrigeration compressor. Piezoresistive pressure transmitters (PPT) and resistance temperature

Nanoarchitectonics of photothermal materials to enhance the sensitivity of lateral flow assays

• Elangovan Sarathkumar,
• Rajasekharan S. Anjana and
• Ramapurath S. Jayasree

Beilstein J. Nanotechnol. 2023, 14, 988–1003, doi:10.3762/bjnano.14.82

• analytes using LFAs. One of the promising strategies is to enhance the photothermal properties of nanomaterials to generate heat after light irradiation, followed by a temperature measurement to detect and quantify the analyte concentration. Recently, it has been observed that the nanoscale architecture of

The nanomorphology of cell surfaces of adhered osteoblasts

• Christian Voelkner,
• Mirco Wendt,
• Regina Lange,
• Max Ulbrich,
• Martina Gruening,
• Susanne Staehlke,
• Barbara Nebe,
• Ingo Barke and
• Sylvia Speller

Beilstein J. Nanotechnol. 2021, 12, 242–256, doi:10.3762/bjnano.12.20

• room temperature. Measurement principle and data preparation Scanning electron microscopy (SEM) was performed using a field-emission SEM (Gemini Supra 25, Zeiss) at 1 keV electron energy without Au coating. For SICM a commercial AFM/SICM setup (NX-bio, Park Systems, Korea) with a live-cell chamber (5

Seebeck coefficient of silicon nanowire forests doped by thermal diffusion

• Shaimaa Elyamny,
• Elisabetta Dimaggio and
• Giovanni Pennelli

Beilstein J. Nanotechnol. 2020, 11, 1707–1713, doi:10.3762/bjnano.11.153

• )/ Finite-element modeling has been used to refine the temperature measurement (see our previous publication [23] for more details). Samples of different lengths, obtained after different etching times, and with different doping temperatures, have been fabricated and measured. The plot of Figure 2 shows ℜ

Influence of the epitaxial composition on N-face GaN KOH etch kinetics determined by ICP-OES

• Markus Tautz,
• Maren T. Kuchenbrod,
• Joachim Hertkorn,
• Robert Weinberger,
• Martin Welzel,
• Arno Pfitzner and
• David Díaz Díaz

Beilstein J. Nanotechnol. 2020, 11, 41–50, doi:10.3762/bjnano.11.4

• centrifuge vials under magnetic stirring. The temperature was precisely maintained with an uncertainty of ±1.5 °C, using an ethylene glycol heating bath and an IR laser thermometer. The credibility of temperature measurement was evaluated by comparison between IR and capillary thermometers. Before immersion

Time-resolved universal temperature measurements using NaYF₄:Er³⁺,Yb³⁺ upconverting nanoparticles in an electrospray jet

• Kristina Shrestha,
• Arwa A. Alaulamie,
• Ali Rafiei Miandashti and
• Hugh H. Richardson

Beilstein J. Nanotechnol. 2018, 9, 2916–2924, doi:10.3762/bjnano.9.270

• ability to be used as a universal temperature sensor. Herein, we introduce a universal calibration protocol for NaYF4:Er3+,Yb3+ upconverting nanoparticles that is robust to environmental changes and gives a precise temperature measurement. We used this new procedure to calculate the temperature profile

• temperature measurement if the entire peak shape is integrated in the calibration. Our universal calibration circumvents this problem and can be used for time-resolved applications. The temperature at the end of the Taylor cone increases due to the creation of a whispering gallery mode cavity with 980 nm

• understand temperature-dependent reactions such as protein unfolding inside microjet/microdroplets and microfluidic systems. Keywords: electrospray; microjet; nanothermometry; temperature measurement; time-resolved measurement; upconverting nanoparticles; Introduction There is need and interest to non

Synthesis of LiNbO₃ nanoparticles in a mesoporous matrix

• Anett Grigas and
• Stefan Kaskel

Beilstein J. Nanotechnol. 2011, 2, 28–33, doi:10.3762/bjnano.2.3

• choice of the lamp. In the focal line of a gold plated cylinder with an elliptic profile, resides an IR radiator focusing the radiation in the second focal line where the sample is located inside a quartz tube flow reactor. Temperature measurement and control is carried out via a NiCr-Ni thermocouple